DIR Return Create A Forum - Home
---------------------------------------------------------
EAGER BEAVER FORUM
HTML https://maamchristine.createaforum.com
---------------------------------------------------------
*****************************************************
DIR Return to: General Discussion
*****************************************************
#Post#: 64--------------------------------------------------
Re: Soldering
By: abogada Date: August 15, 2016, 9:11 am
---------------------------------------------------------
When the soldering tip didn't heat so that i cant melt the lead.
#Post#: 65--------------------------------------------------
Re: Soldering
By: epino Date: August 15, 2016, 9:58 am
---------------------------------------------------------
the problems that I've encountered during soldering are: first,
stripping the copper wire manually using hand tools (not
including wire stripper). Though I've experienced stripping
wires when i was an electrical student, but this time it's more
difficult cause the size of the wire are thinner than what we
are using in electrical wiring. second, we really had a hard
time making the lead stick to the copper wire. Maybe because we
didn't scratch it properly using a sand paper. and the third, i
struggled making the lead smooth and alined in both sides. I
surpassed those struggles by trying again and again until i got
the techniques on how you properly solder a copper wire.
#Post#: 69--------------------------------------------------
Re: Soldering
By: crml19 Date: August 15, 2016, 8:20 pm
---------------------------------------------------------
The common problem that I encountered is whenever I solder, I
end up like having a lot of lead kisses on the table hahaha!! I
cant solder well :( :( :p
#Post#: 86--------------------------------------------------
Re: Soldering
By: Carlyn Date: August 15, 2016, 10:44 pm
---------------------------------------------------------
The common problems we encounter in soldering is the wattage and
the amount of lead we use in the given sizes of wires. Some
soldering iron have low wattage that cannot easily let the
soldering lead melt faster. And we must use less soldering lead
if the wires we are using are small.
#Post#: 87--------------------------------------------------
Re: Soldering
By: arjuyy Date: August 15, 2016, 10:49 pm
---------------------------------------------------------
For me the most commonly problem i've encounter is the round
shape like led while soldering the wires and i cant help it
because im a beginner and to overcome it i've watch videos in
youtube about soldering.
#Post#: 93--------------------------------------------------
Re: Soldering
By: domalaon Date: August 16, 2016, 7:25 am
---------------------------------------------------------
the problem i encounter is i don`t know how much lead i will
apply on those wire ( first project ung parang banig heheh) ;D
#Post#: 108--------------------------------------------------
Re: Soldering
By: ckmoli Date: August 17, 2016, 2:52 am
---------------------------------------------------------
The heat from the soldering tip. Sometimes the heat does not
melt the lead but I find the hottest part on the tip so I can
use it again.
#Post#: 144--------------------------------------------------
Re: Soldering
By: puroylan Date: August 21, 2016, 1:45 am
---------------------------------------------------------
Hindi nainit yung tip ng soldering. Then kinaskas ko yung tip ng
liha/sand paper kaya ayun OK na ;D
#Post#: 147--------------------------------------------------
Re: Soldering
By: Luis Gabelo Date: August 21, 2016, 11:42 am
---------------------------------------------------------
[quote author=puroylan link=topic=2.msg144#msg144
date=1471761904]
Hindi nainit yung tip ng soldering. Then kinaskas ko yung tip ng
liha/sand paper kaya ayun OK na ;D
[/quote]
ang common ng problem na ito, paano po ba ito maiiwasan mam?
#Post#: 153--------------------------------------------------
Re: Soldering
By: jhoy Date: August 21, 2016, 11:51 am
---------------------------------------------------------
[quote author=Luis Gabelo link=topic=2.msg147#msg147
date=1471797739]
[quote author=puroylan link=topic=2.msg144#msg144
date=1471761904]
Hindi nainit yung tip ng soldering. Then kinaskas ko yung tip ng
liha/sand paper kaya ayun OK na ;D
[/quote]
ang common ng problem na ito, paano po ba ito maiiwasan mam?
[/quote]
Best way na yung pagliha ng tip bago at pagkatapos gamitin para
maalis yung mga dumi na kumapit sa tip.
*****************************************************
DIR Previous Page
DIR Next Page