DIR Return Create A Forum - Home
---------------------------------------------------------
Hi Point Cafe Forum
HTML https://hipointcafeforum.createaforum.com
---------------------------------------------------------
*****************************************************
DIR Return to: Carbine Modifications
*****************************************************
#Post#: 1039--------------------------------------------------
Anybody hear of any New Accessories?
DIR By: Mach O Melvin
Date: March 13, 2018, 3:34 pm
---------------------------------------------------------
There has got to be something NEW coming around the mountain?
#Post#: 1044--------------------------------------------------
Re: Anybody hear of any New Accessories?
DIR By: Brother Brian
Date: March 15, 2018, 6:06 am
---------------------------------------------------------
Weird. I posted a reply to this yesterday but it's gone
I haven't heard of any new accessories yet, but Hi Point did
update it's website
--- Quote ---
> If you have not been to the HI-Point Firearms site in a while
go check it out to see some page updates.
>
> One of the newest options is when searching for a Carbine you
now just select the caliber as before we had it listed as Black
carbines and Camo carbines.
>
> The OD&FDE and the Hunters are now listed under the Carbines
tab along with the California Compliant (all calibers available
are under each one.)
>
> The link below will take you to the 10mm page where you can
see both the 1095TS and the 1095TS Edge.
>
> Also the Buy Now options are for black and camo options are at
the bottom of the page.
--- End Quote ---
HTML https://www.hi-pointfirearms.com/index.html
#Post#: 1046--------------------------------------------------
Re: Anybody hear of any New Accessories?
DIR By: CaptREDD
Date: March 16, 2018, 12:01 pm
---------------------------------------------------------
In regards to a NEW accessories, sure would be nice if Hi-Point
would make a muzzle-brake to screw on the threaded barrel
carbines.
As I think they would be better than the clamp-on kind!
REDD
#Post#: 1049--------------------------------------------------
Re: Anybody hear of any New Accessories?
DIR By: Delbert
Date: March 16, 2018, 2:45 pm
---------------------------------------------------------
Redd, for a screw on muzzle brake you do a thread pitch and
purchase ANY brake made for that diameter and thread count. It
should be 1/2x28 or 9/16x24 I believe. Just don't forget an
assortment of peel off brake washers to clock the brake
correctly, if needed.
I read a write up on this model, but don't remember what they
said about the barrel screw on protector size. When HP decided
to come out with this carbine, it was their intention of people
putting on suppressors for hunting with.
I have a 4095TS model and it has a barrel diameter of
0.659"(with factory barrel paint), so when cutting down for
threading, it should be somewhere around the 1/2x28 size.
Take your thread protector nut off and go to a gun shop that
has a gunsmith or take it to a home/farm store and you should be
able to find a thread size/pitch plate hanging off a post in the
nuts/bolts aisle. That will tell you immediately.
#Post#: 1050--------------------------------------------------
Re: Anybody hear of any New Accessories?
DIR By: CaptREDD
Date: March 16, 2018, 5:30 pm
---------------------------------------------------------
Delbert,
the 1095TS has a threaded barrel from the factory... .57x28
according to factory manual.
REDD
#Post#: 1051--------------------------------------------------
Re: Anybody hear of any New Accessories?
DIR By: Delbert
Date: March 16, 2018, 11:57 pm
---------------------------------------------------------
--- Quote from: CaptREDD link ---
>
> Delbert,
> the 1095TS has a threaded barrel from the factory... .57x28
according to factory manual.
>
>
> REDD
>
--- End Quote ---
I understand Redd. I didn't word it correctly. I looked more
into the 10mm HP carbine thread size and pitch. It does have
1/2x28 threads. Just find a screw on brake or compensator for
either 40 S&W caliber or 10mm and you'll be good as long as you
get the correct thread size and pitch as the attachment.
Being an old apprentice machinist when measuring with calipers
1/2"(inch) converts to .500"(some might say .5", .50", or .500")
on a measurement chart. So, having a barrel end thread at
.57"(.07" hundred thousands) difference between a threaded brake
drill/tap size and the barrel's threaded size. This will give
the brake/compensator or suppressor a good tight seal, while
still going on or coming off, without any undue stress of the
threads over time.
Del
#Post#: 1053--------------------------------------------------
Re: Anybody hear of any New Accessories?
DIR By: Delbert
Date: March 17, 2018, 6:45 pm
---------------------------------------------------------
--- Quote from: Mach O Melvin link ---
>
> There has got to be something NEW coming around the mountain?
>
--- End Quote ---
With the new 1095 carbine that's now come out with its threaded
barrel, it's gonna be tough to find 1/2x28 TPI barrel Brakes and
Compensators.
Well I was just looking online and I found a Linear Comp that
will work.
Seller: Joe Bob Outfitters.
Made by: Kaw Valley Precision(KVP).
Model(s): XL and "Slim" XL.
Will fit: 40S&W / 10MM and 45ACP (or) smaller calibers using
1/2x28 TPI.
Cost: Less than $50 for either choice.
#Post#: 1225--------------------------------------------------
Re: Anybody hear of any New Accessories?
DIR By: JW
Date: September 16, 2018, 12:41 am
---------------------------------------------------------
Here's some cool stuff I found,
HTML https://jsarmsco.com/#!/Hi-Point-Carbine-parts/c/30933262/offset=0&sort=normal
#Post#: 1226--------------------------------------------------
Re: Anybody hear of any New Accessories?
DIR By: Mach O Melvin
Date: September 16, 2018, 4:07 am
---------------------------------------------------------
Thanks for posting, I know I'll be looking soon!
*****************************************************
Page 1 of 1