DIR Return Create A Forum - Home
---------------------------------------------------------
Chainsaw Repair
HTML https://chainsawrepair.createaforum.com
---------------------------------------------------------
*****************************************************
DIR Return to: McCulloch
*****************************************************
#Post#: 40267--------------------------------------------------
Re: Powermac 6 died
DIR By: super44
Date: May 16, 2014, 4:10 pm
---------------------------------------------------------
That does look like the one, but out of stock. I have 2 of
these things so I guess for now I will make 1 good one out of
the good parts and get the coil at a later date. I see one on
Ebay but that one is a little much with shipping.
#Post#: 40268--------------------------------------------------
Re: Powermac 6 died
DIR By: 660magnum
Date: May 16, 2014, 4:35 pm
---------------------------------------------------------
I didn't notice the out of stock
Chainsawr had several listed but they were out of stock also.
you might could call these guys and see if they have one out
back that they have not stripped down yet?
#Post#: 40334--------------------------------------------------
Re: Powermac 6 died
DIR By: mowertech
Date: May 18, 2014, 7:10 pm
---------------------------------------------------------
Ever thought of getting one from a source you know will
treat you right ? I sell them for $ 3.90 plus shipping
if you need a coil; i may be able to assist in that as
well
#Post#: 40336--------------------------------------------------
Re: Powermac 6 died
DIR By: super44
Date: May 18, 2014, 8:58 pm
---------------------------------------------------------
--- Quote from: mowertech link ---
>
> Ever thought of getting one from a source you know will
treat you right ? I sell them for $ 3.90 plus shipping
if you need a coil; i may be able to assist in that as
well
>
--- End Quote ---
I did get the filters, tell me more about your coils.
#Post#: 40390--------------------------------------------------
Re: Powermac 6 died
DIR By: super44
Date: May 20, 2014, 12:55 pm
---------------------------------------------------------
I guess Monday was not a good day for working on my current mold
project so then what to work on?? Power Mac 6! I took the coil
off my older model and put it on this saw, rebuilt the carb also
and put her back together and set it down. Today at lunch I put
in some gas & oil, primed the carb and 2 pulls later it was
running. It will even sit and idle for a while so after a few
times of running and tuning I think it will be fine.
#Post#: 40461--------------------------------------------------
Re: Powermac 6 died
DIR By: Bad Xmpl
Date: May 22, 2014, 12:53 pm
---------------------------------------------------------
I realize that everyone doesn't have this stuff around and it's
kinda expensive but if you have K&N air filters on ANYTHING you
may also have the cleaner and oil. I just spray the cleaner on,
wait 5 minutes and wash it out. Air dry. it's made for removing
filter oil and dirt, so it's the perfect stuff. If you don't
have the cleaner, use some dish soap and water. The soap will
soften the soaked in oil and you can rinse it out with water.
Air dry (not pressure air; just let it sit) See if that helps.
Good luck!
#Post#: 40500--------------------------------------------------
Re: Powermac 6 died
DIR By: super44
Date: May 23, 2014, 3:12 pm
---------------------------------------------------------
Ran a tank of gas through the Mac 6 today on a maple top with no
issues. Good little saw!
#Post#: 42357--------------------------------------------------
Re: Powermac 6 died
DIR By: super44
Date: July 4, 2014, 7:56 pm
---------------------------------------------------------
Today my wife wanted to use a chainsaw to cut down a dead apple
tree in our yard. Since she is a small woman I figured Power Mac
6, after all it ran OK last time. It start OK but died after a
bit and would only fire if I put gas down the intake. So I got
out my Homlite Super EZ which is a bit much for her and she cut
down her first tree using a chainsaw. Vahooo!! So stuff that
should run and won't just ticks me off so my PM 6 will get a
complete refurb. 1st question is what are the crankshaft seals
PN? I have a "few" other saws so this one my be a "I'm snowed
in with nothing else to do" day project.
*****************************************************
Page 2 of 2
DIR Previous Page