DIR Return Create A Forum - Home
---------------------------------------------------------
Chainsaw Repair
HTML https://chainsawrepair.createaforum.com
---------------------------------------------------------
*****************************************************
DIR Return to: Partner
*****************************************************
#Post#: 5845--------------------------------------------------
partner 5000 on/off switch
DIR By: Jeff
Date: December 25, 2011, 11:22 am
---------------------------------------------------------
Guys I hope i dont seem to be hogging your forum or time but i
do have a question.
On my 5000's the switch is a regular problem the "female ?"
wire connector that is slid into the bottom of the red plastic
switch always seems to not stay in place or the wire itself is
too stiff or somthing always keeps me from being able to use my
switchs so I have to choke the saws to shut them off. If you
have used a 5000 for very long you probably know what I mean
this just seems to be a design flaw of sorts to me. I did on one
saw replace the stiff wire with a more flexable one and that
does work better, is there a easy or better way to keep the
switch working better?
Also In vocational school we learned that a turn and a quarter
on High and Low speed jets will most often be close enough to
get a saw started. I tend to have to adjust these settings a
couple of times per season is this normal? I figure the screws
may be working out due to vibration. Does anyone else experience
this sort of thing? Thanks for your time and if you can see I am
going to be a problem already by asking too many questions just
say so. Jeff
#Post#: 5847--------------------------------------------------
Re: partner 5000 on/off switch
DIR By: Chainsawrepair
Date: December 25, 2011, 12:29 pm
---------------------------------------------------------
Ask away. Thats what I started this site for to help people and
that is why I seeked out people in the beginning that knew about
certain saw makes etc to be here and help.
Yes the on/off is a issue I have dealt with more then once too.
I have had the wire break at the female end and put a new
connector on instead of using the old one. Watch with top off
and pay attention to wire moment. Move wire to keep from pulling
on it has solved my issues.
Carb 1.25 start is in the range I do. I have started at 1 to 1.5
turn. Never had the 5000 stock carbs creep on me. But have had
to adjust for weather changes. warm to cold, cold to warm etc.
Do you have the little springs behind your H and L?
#Post#: 5856--------------------------------------------------
Re: partner 5000 on/off switch
DIR By: Jeff
Date: December 25, 2011, 2:17 pm
---------------------------------------------------------
Yes I do have the springs it is not really that big a deal I can
live with the adjustment I guess.I just came in from the shop
and I re-wired 2 of the saws with smaller more flexable wire. I
also had to make a strap to replace the one at the front of the
handle bar where it attaches to the saw body .I could not find
one so I made one from a nylon braided garden hose it will work
for now but I will need to pick one up. I go through them
compleatly every so often so today was the day probably cut some
wood tomorrow.
#Post#: 5865--------------------------------------------------
Re: partner 5000 on/off switch
DIR By: TORX
Date: December 25, 2011, 4:16 pm
---------------------------------------------------------
What i do with the wire conector is just spread it out so it
fits tighter in the red switch.
#Post#: 5866--------------------------------------------------
Re: partner 5000 on/off switch
DIR By: Jeff
Date: December 25, 2011, 4:23 pm
---------------------------------------------------------
Yes I have done that also I have also used a small screw and an
eyelet wire end and screwed ti to the under side of a old red
plastic switch that had one side split away that works pretty
well.
#Post#: 5867--------------------------------------------------
Re: partner 5000 on/off switch
DIR By: TORX
Date: December 25, 2011, 4:46 pm
---------------------------------------------------------
Lol. I've did the redneck screw fix also. ;)
#Post#: 5880--------------------------------------------------
Re: partner 5000 on/off switch
DIR By: Jeff
Date: December 25, 2011, 6:18 pm
---------------------------------------------------------
By God it works though dont it? I dont always have the right
stuff but the wood dont know that! Glad i'm not alone.
#Post#: 6100--------------------------------------------------
Re: partner 5000 on/off switch
DIR By: chainsman1
Date: December 29, 2011, 9:57 pm
---------------------------------------------------------
For mine,i did get tired of fighting with that switch,so i did a
hole in the air filter cover and installed a good toggle switch
and never had trouble again. Right over the old switch
#Post#: 6105--------------------------------------------------
Re: partner 5000 on/off switch
DIR By: Jeff
Date: December 30, 2011, 7:03 am
---------------------------------------------------------
Thats a idea
*****************************************************
Page 1 of 1