DIR Return Create A Forum - Home
       ---------------------------------------------------------
       Chainsaw Repair
  HTML https://chainsawrepair.createaforum.com
       ---------------------------------------------------------
       *****************************************************
   DIR Return to: Trades Swap Section
       *****************************************************
       #Post#: 54263--------------------------------------------------
       NOS Poulan bars 32 36 
   DIR By: Cut4fun
       Date: February 14, 2015, 11:54 am
       ---------------------------------------------------------
       If you run .404 or have a 3/8 tip.
  HTML http://www.ebay.com/itm/32-Poulan-Sprocket-Nose-Guide-Bar-/111578118310?pt=LH_DefaultDomain_0&hash=item19fa92f8a6
  HTML http://www.ebay.com/itm/36-Poulan-Sprocket-Nose-Guide-Bar-/111578119624?pt=LH_DefaultDomain_0&hash=item19fa92fdc8
       #Post#: 54265--------------------------------------------------
       Re: NOS Poulan bars 32 36 
   DIR By: Cut4fun
       Date: February 14, 2015, 12:16 pm
       ---------------------------------------------------------
       Anyone tell the bar mount on 36 etc?
       #Post#: 54280--------------------------------------------------
       Re: NOS Poulan bars 32 36 
   DIR By: Eccentric
       Date: February 14, 2015, 3:28 pm
       ---------------------------------------------------------
       Windsor UXL.  That's basically the same as an Oregon D096.  3/8"
       (9.5mm) slot.  Homelite XL-series mount.  SXL-AO, SXL-925,
       450/550/650/750, etc.  The UXL bars I've seen also have oil
       passages from the adjuster slots to the chain groove (in
       addition to the separate oil holes).  They can be used on a
       later XL-series (3/8" stud) Homelite, a Poulan 6900/7700/8500,
       or a late (3/8" stud) Poulan 4400/4900/5400 (some of those were
       equipped with 5/16" studs, others with 3/8" studs).
       Windsor never made an A176/D176 type 5/16" slot
       Homelite/Echo/Poulan/etc mount bar.  Instead, they sold the UXL
       mount bars with an 'S' type stud spacer for use on 5/16" stud
       saws.  That's how these bars were supplied for Poulan.  I have a
       306A that came to me with a 20" UXL mount bar and an 'S' clip.
       Has the Poulan part # that's in the IPL.  The IPL's show these
       bars and the 'S' clips.  The piece of masking tape across the
       stud slots of the bars in the ebay listings held the 'S' clip in
       place until the bar was sold.  Can't see if the 'S' clips are
       still there.............or if they have escaped.
       McCulloch did a similar thing with some Oregon and Windsor
       manufactured bars.  They have a 3/8" stud slot (suitable for the
       large frame Macs so long as they have the right bar plates), and
       were sold with spring type stud spacers held in the slot with
       tape.
  HTML http://www.acresinternet.com/cscc.nsf/14711d8004b6ea7c88256e0c0001ff32/c0ac3eaf85163b9c88256e0e001fa1fe?OpenDocument
       [img width=600
       height=351]
  HTML http://www.acresinternet.com/cscc.nsf/14711d8004b6ea7c88256e0c0001ff32/c0ac3eaf85163b9c88256e0e001fa1fe/Body/0.84?OpenElement&FieldElemFormat=gif[/img]
       #Post#: 54282--------------------------------------------------
       Re: NOS Poulan bars 32 36 
   DIR By: Eccentric
       Date: February 14, 2015, 3:49 pm
       ---------------------------------------------------------
       I have a bunch of those 3-rivet 3/8" pitch Windsor tips.  Could
       sell/trade some if needed for these bars.  The current 5-rivet
       Windsor tips won't work on those older Windsor bars.
       Kevin I went through his items index.  I think I see what got
       you to his listings. 8)
       He also has the bare bore version 46cc cylinders (and the
       corresponding pistons).   Wish he had the chromed bore versions.
       I put those into Husky 36-141 saws (with some intake side parts
       mixing/matching as well).
       He does have pistons for the 49cc clamshell Poulans (like the
       50th anniversary 315 in another thread here).  I wish he had the
       cylinders for those.  I want to put one of the 49cc P/C's into a
       Husky 36-141 series saw like I do with the 46cc versions.
       He also has cylinders for the PP235 and PP236.  Unfortunately he
       doesn't have pistons too.
       #Post#: 54289--------------------------------------------------
       Re: NOS Poulan bars 32 36 
   DIR By: Chainsawrepair
       Date: February 14, 2015, 4:20 pm
       ---------------------------------------------------------
       Thanks for that info.  Yep came across bars in other searching.
       ;)
       *****************************************************
       Page 1 of 1