DIR Return Create A Forum - Home
---------------------------------------------------------
Chainsaw Repair
HTML https://chainsawrepair.createaforum.com
---------------------------------------------------------
*****************************************************
DIR Return to: Homelite
*****************************************************
#Post#: 31468--------------------------------------------------
Homelite 1050 model ?
DIR By: Cut4fun
Date: January 11, 2014, 3:48 pm
---------------------------------------------------------
Was told homelite 1025 , took model off heading because I
couldn't find a 1025. Guess I wont know for sure till I see the
saw now.
Well I dont see a 1025, maybe he meant 925 1020 1050 1000 1130
or something
What to look at if taking in trade or buying one? Going prices
for runner? Just ball park.
I'll start searching for info myself too. In between watching
playoff football. :P
#Post#: 31470--------------------------------------------------
Re: Homelite model ?
DIR By: Eccentric
Date: January 11, 2014, 4:06 pm
---------------------------------------------------------
--- Quote from: Cut4fun link ---
>
> Was told homelite 1025 (guessing 100cc)
>
> Well I dont see a 1025, maybe he meant 925 1020 1050 1000
1130 or something
>
>
> What to look at if taking in trade or buying one? Going
prices for runner? Just ball park.
>
> I'll start searching for info myself too. In between watching
playoff football. :P
>
--- End Quote ---
Yeah there was no Homelite 1025 from what I know. More than
likely a SXL-925 or XP1020 or 1050 as you stated. 'Worth' is
difficult, and depends on saw condition more than anything else.
Look for the usual. Pull the muffler cover and peek at the
P/C. As with most old saws, many people tune them too lean and
burn up the P/C (and/or the saw develops an air leak from bad
crank seals or leaking gaskets and does the same thing). NOS
pistons and cylinders will costya $150-$200 for the pair.
Also look at the bottom of the saw for broken bits and/or
corrosion. If it's an XP-1020 or 1050 it should have a mag
muffler shield. They're often missing or broken. Check the
crankcase at the bottom where it meets the flywheel cover and
where the handlebar attaches. They are often busted from rough
handling.
On the XP-1020 and 1050 also check the bar pad and underside of
the clutch cover for chain rash. People often put the wrong
bars (usually D096/D196/UXL XL-series bars) on these saws
instead of the correct F014 bars.....................and that
leads to damage because the bar tail is too narrow on those for
the saws.
If you can get a pic or two I can give you more help regarding
identification and value. Having an intact MN/SN tag (or decal)
helps value too, and is often missing from these old beasts.
Rough value estimates for a runner with a good P/C and no busted
or badly corroded bits is probably $100-$250. More for cherry
and complete examples (especially for the XP-1020 and 1050 if
they have a correct bar in good
shape.....................especially a longer one). Much less
for beaten/broken saws or ones with roached P/C's. Ebay values
for SXL-925 and XP-1020/1050 runners have varied wildly. Some
nice ones have gone for $400-$500. Others in similar condition
have gone for less than 1/2 that...
#Post#: 31471--------------------------------------------------
Re: Homelite model ?
DIR By: Chainsawrepair
Date: January 11, 2014, 4:09 pm
---------------------------------------------------------
Thanks for info. Will know more only IF and when saw shows
up.
I am only looking at it to pass onto someone else. Guy said
something about just putting a new bar and chain on it for a
$100
I've seen 925's list 100 to 325. I thought the 325 was high at a
dealers.
#Post#: 31472--------------------------------------------------
Re: Homelite model ?
DIR By: Eccentric
Date: January 11, 2014, 4:12 pm
---------------------------------------------------------
--- Quote from: Cut4fun_ link ---
>
> Thanks for info. Will know more only IF and when saw shows
up.
>
> I am only looking at it to pass onto someone else. Guy said
something about just putting a new bar and chain on it for a
$100
>
--- End Quote ---
You're welcome Kevin. Added a bit more (in an edit) while you
were posting...
#Post#: 32002--------------------------------------------------
Re: Homelite model ?
DIR By: Chainsawrepair
Date: January 17, 2014, 4:21 pm
---------------------------------------------------------
Owner called and left message today while at work. Wants me to
check over a new to him 395xp.
Hopefully I remember to tell him to bring the homie too. Then I
can get pics for someone if they are interested in whatever it
is.
#Post#: 32040--------------------------------------------------
Re: Homelite 1050 model ?
DIR By: Cut4fun
Date: January 17, 2014, 7:08 pm
---------------------------------------------------------
Called back and we talked. Homelite 1050 is the saw in
question. He said thinking seal going.
HTML http://www.acresinternet.com/cscc.nsf/ed1d619968136da688256af40002b8f7/ffb71738fc8561cb88256db200126951?OpenDocument
Homelite 1050 bar mount.
HTML http://www.acresinternet.com/cscc.nsf/BMP/16?OpenDocument
? this bar mount looks like it could work on the 395xp, anyone
know for sure or any adjustments needed to oiler holes etc.
395 bar mount
HTML http://www.acresinternet.com/cscc.nsf/14711d8004b6ea7c88256e0c0001ff32/54f3341de6d0d70b88256e0e001fda90?OpenDocument
#Post#: 32044--------------------------------------------------
Re: Homelite 1050 model ?
DIR By: Eccentric
Date: January 17, 2014, 8:04 pm
---------------------------------------------------------
Acres listing for the D009 large Husky mount is in error.
States that the slot is 9.5mm (3/8") when it's actually 9mm.
That F014 large Homelite mount really isn't suitable for use on
a large Husky (and the reverse is true too). The tail profile
of the F014 is much broader, and the oiler holes are much
farther apart.
Also, longer F014 mount bars (especially sprocket noses) are
getting hard to come by. Be a shame to butcher one up to run on
a D009 application saw when the D009 mount bars are so common.
A fellow who ends up with an F014 mount bar (that they don't
need for an F014 saw) can easily sell it for more than what it'd
cost to get a same-length (or longer) D009 mount bar.
The D009 is closer to a D096/D196/UXL Homelite XL-series mount
bar (SXL-925, etc) or a D176 mount Poulan/Echo bar. Still
pretty far apart from them however. The D096 has a 3/8" (9.5mm)
slot and the D176 has a 5/16" (8.22mm) slot. The tail profiles
of the D096 and D176 bars are still broader than the D009 mount
bar, but not to the same degree as the difference between an
F014 and D009. I'll shoot some pics of the different bar tails
this weekend and post them up to illustrate.
Guys have ran D009 mount bars on D096 and D176 application saws
without issues..................but I've also seen damage done
to saws from that practice. I have a Poulan 5200 crankcase
that's damaged from when somebody was running an H005 (earlier
D009 mount bar) on it. The 5200 takes a D176.
I've also seen damage from guys running D096/D196 Homelite XL
mount bars on Homelite F014 large frame saws. Same problems
(chain rash from the narrower tail) as well as the chain not
being oiled for shit because the narrower D096 bar doesn't even
completely cover the oiler slot on the bar pad of an F014
application saw. Just because the slot's the same (both are
3/8") that doesn't mean that there won't be other issues....
#Post#: 32052--------------------------------------------------
Re: Homelite 1050 model ?
DIR By: Chainsawrepair
Date: January 17, 2014, 10:37 pm
---------------------------------------------------------
Thanks for the post. Hopefully he reads this (he is a member
here now).
I knew the lg husky mount 9mm part but not the rest on
comparison. Thank you for info.
I told him to compare to bars laid on top of each other, because
I didnt know what the 1050 bar looked like beside that mount
pic.
#Post#: 33711--------------------------------------------------
Re: Homelite 1050 model ?
DIR By: gunrac
Date: February 7, 2014, 6:33 pm
---------------------------------------------------------
Finally taking time to look around.........thx for the info guys
#Post#: 33713--------------------------------------------------
Re: Homelite 1050 model ?
DIR By: Eccentric
Date: February 7, 2014, 6:45 pm
---------------------------------------------------------
Welcome to the site.
*****************************************************
Page 1 of 2
DIR Next Page