PURE DATA, LTD. =============== SATISFAXTION MODEM/200 Card Type Modem(asynchronous) Chip Set Intel Maximum Data Rate 2400bps Maximum Fax Rate 9600bps Data Bus 16 bit ISA Fax Class Class I & II Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis Fax Modulation Protocol Unidentified Error Correction/Compression MNP5, V.42, V.42bis +------------------------------------------------------------+ | CONNECTIONS | |------------------------------------------------------------| | Function | Label | Function | Label | |------------------------------------------------------------| | Line in | CN1 | Unidentified | CN3 | |---------------------------+----------+--------------+------| | Line out | CN2 | | | +------------------------------------------------------------+ Proprietary AT Command Set +------------------------------------------------------------+ | ACCEPT RELIABLE CONNECTION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \U [cmds] | |--------------+---------------------------------------------| | Description: | Accepts remote modem's request for MNP | | | reliable link. | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RELIABLE FALLBACK CHARACTER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] %An [cmds] | |--------------+---------------------------------------------| | Default: | 19 | |--------------+---------------------------------------------| | Range: | 0-127 | |--------------+---------------------------------------------| | Unit: | ASCII | |--------------+---------------------------------------------| | Description: | Sets the character used as the | | | auto-reliable fallback character | +------------------------------------------------------------+ +------------------------------------------------------------+ | AUTO-RELIABLE TIME BUFFER CONFIGURATION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Cn [cmds] | |--------------+---------------------------------------------| | Description: | Controls the handling of incoming data | | | during auto-reliable time period | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \CO | Disabled | |--------------+---------------------------------------------| | \C1 | Enable 200 character buffer. If 200 | | | characters received without reliable | | | character, establish normal connection | |--------------+---------------------------------------------| | \C2 | Auto reliable buffer disabled. Establish | | | normal connection on receipt of escape | | | character | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S14 | |------------------------------------------------------------| | Format | AT [cmds] S14=n [cmds] | |--------------+---------------------------------------------| | Default: | 138 | |--------------+---------------------------------------------| | Range: | 0-174 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls echo, result codes, result code | | | display, dial mode, and answer/originate | | | mode | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Not used | |------+-------+---------------------------------------------| | 1 | 0 | Command echo disabled | | | | | | | i 1 | Command echo enabled | |------+-------+---------------------------------------------| | 2 | i 0 | Result codes enabled | | | | | | | 1 | Result codes disabled | |------+-------+---------------------------------------------| | 3 | 0 | Display result codes in numeric format | | | | | | | i 1 | Display result codes in verbose format | |------+-------+---------------------------------------------| | 4 | 0 | Not used | |------+-------+---------------------------------------------| | 5 | i 0 | Tone dial enabled | | | | | | | 1 | Pulse dial enabled | |------+-------+---------------------------------------------| | 6 | 0 | Not used | |------+-------+---------------------------------------------| | 7 | 0 | Answer mode enabled | | | | | | | i 1 | Originate mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S21 | |------------------------------------------------------------| | Format | AT [cmds] S21=n [cmds] | |--------------+---------------------------------------------| | Default: | 48 | |--------------+---------------------------------------------| | Range: | 0 - 254 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls S23, CTS action, DTR action, DCD | | | action, DSR action and the Long Space | | | Disconnect function. | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Not used | |------+-------+---------------------------------------------| | 1 | 0 | Option 1 for bits 1, 2 and 3 of S32 enabled | | | | | | | 1 | Option 2 for bits 1, 2 and 3 of S23 enabled | |------+-------+---------------------------------------------| | 2 | i 0 | CTS signal normal | | | | | | | 1 | CTS signal forced high | |------+-------+---------------------------------------------| | 4, 3 | 00 | DTR signal ignored | | | | | | | 01 | Modem goes to command mode on low DTR | | | | | | | i 10 | Modem disconnects on low DTR. Auto-Answer | | | | is disabled | | | 11 | | | | | Modem is initialized on low DTR | |------+-------+---------------------------------------------| | 5 | 0 | DCD signal forced high | | | | | | | i 1 | DCD signal normal | |------+-------+---------------------------------------------| | 6 | i 0 | DSR signal forced high | | | | | | | 1 | DSR signal normal | |------+-------+---------------------------------------------| | 7 | i 0 | Long Space Disconnect function disabled | | | | | | | 1 | Long Space Disconnect function enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S22 | |------------------------------------------------------------| | Format | AT [cmds] S22=n [cmds] | |--------------+---------------------------------------------| | Default: | 118 | |--------------+---------------------------------------------| | Range: | 0-255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls speaker, result codes and | | | make/break ratio | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 1, 0 | 00 | Off volume | | | | | | | 01 | On volume | | | | | | | i 10 | Medium level volume | | | | | | | 11 | High level volume | |------+-------+---------------------------------------------| | 3, 2 | 00 | Speaker off | | | | | | | i 01 | Speaker off on carrier | | | | | | | 10 | Speaker always on | | | | | | | 11 | Speaker on during handshake | |------+-------+---------------------------------------------| | 6, | 000 | Blind dial and basic result codes only | | 5, 4 | | enabled | | | 100 | | | | | Blind dial and basic and connection speed | | | 101 | result codes enabled | | | | | | | 110 | Blind dial and basic and connection speed | | | | result codes and dialtone detection enabled | | | i 111 | | | | | Blind dial, basic and connection speed | | | | result codes and dialtone detection enabled | | | | | | | | Blind dial, basic and connection speed | | | | result codes, busy and dialtone detection | | | | enabled | |------+-------+---------------------------------------------| | 7 | i 0 | Make/Break pulse ratio at 39/61 | | | | | | | 1 | Make/Break pulse ration at 33/67 | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S23 | |------------------------------------------------------------| | Format | AT [cmds] S23=n [cmds] | |--------------+---------------------------------------------| | Default: | Unidentified | |--------------+---------------------------------------------| | Range: | 0-191 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Grants/denies remote digital loopback, | | | controls DTE rate and parity, and sets | | | guard tone | |------------------------------------------------------------| | Note: See S21 bit one to set option 1 and 2 | |------------------------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Remote digital loopback ignored | | | | | | | i 1 | Remote digital loopback accepted | |------------------------------------------------------------| | Option 1 (bit 1 of S21 = 0) | |------------------------------------------------------------| | 3, | 000 | Sets serial port speed to 0-300bps | | 2, 1 | | | | | 001 | Sets serial port speed to 1200bps | | | | | | | 010 | Sets serial port speed to 2400bps | | | | | | | 011 | Sets serial port speed to 4800bps | | | | | | | 101 | Sets serial port speed to 9600bps | | | | | | | 110 | Sets serial port speed to 19.2Kbps | | | | | | | 111 | Sets serial port speed to 38.4Kbps | |------------------------------------------------------------| | Option 2 (bit 1 of S21 = 1) | |------------------------------------------------------------| | 3, | 000 | Sets serial port speed to 12.0Kbps | | 2, 1 | | | | | 001 | Sets serial port speed to 14.4Kbps | | | | | | | 010 | Sets serial port speed to 57.6Kbps | |------+-------+---------------------------------------------| | 5,4 | 00 | Parity even | | | | | | | i 01 | Parity space/no parity | | | | | | | 10 | Parity odd | | | | | | | 11 | Parity mark | |------+-------+---------------------------------------------| | 7, 6 | 00 | Guard tone disabled | | | | | | | 01 | 550Hz guard tone enabled | | | | | | | i 10 | 1800Hz guard tone enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | BIT-MAPPED REGISTER S27 | |------------------------------------------------------------| | Format | AT [cmds] S27=n [cmds] | |--------------+---------------------------------------------| | Default: | 73 | |--------------+---------------------------------------------| | Range: | 0 - 255 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Controls communications mode, line type, | | | and protocol type | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | 0 | Not used | |------+-------+---------------------------------------------| | 1 | 0 | Not used | |------+-------+---------------------------------------------| | 7, 2 | i00 | Switched line | | | | | | | 01 | Leased line | | | | | | | 10 | Not used | | | | | | | 11 | Leased line | |------+-------+---------------------------------------------| | 3 | 0 | Not used | |------+-------+---------------------------------------------| | 4 | 0 | Not used | |------+-------+---------------------------------------------| | 5 | 0 | Not used | |------+-------+---------------------------------------------| | 6 | i 0 | Select CCITT protocols | | | | | | | 1 | Select Bell protocols | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK SEND | |------------------------------------------------------------| | Type | Configuration | |-------------+----------------------------------------------| | Format | AT [cmds] \Bn [cmds] | |-------------+----------------------------------------------| | Default | 3 | |-------------+----------------------------------------------| | Range | 1 -9 | |-------------+----------------------------------------------| | Unit | .1 second | |-------------+----------------------------------------------| | Description | Sends break of n | +------------------------------------------------------------+ +------------------------------------------------------------+ | BREAK TYPE | |------------------------------------------------------------| | Type: | Configuration | |---------------------+--------------------------------------| | Format: | AT [cmds] \Kn [cmds] | |---------------------+--------------------------------------| | Description: | Configures action of break signal | |------------------------------------------------------------| | Command | Break from | Break from DTE | Break from | | | DTE | while in | remote modem | | | | command mode | | |------------+-------------+-----------------+---------------| | \K0 | Enter | Buffers cleared | Buffers | | | command | and break sent | cleared and | | | mode, do | to remote modem | break sent to | | | not send | | remote modem | | | break to | | | | | remote | | | | | modem | | | |------------+-------------+-----------------+---------------| | \K1 | Buffers | Buffers cleared | Buffers | | | cleared and | and break sent | cleared and | | | break sent | to remote modem | break sent to | | | to remote | | remote modem | | | modem | | | |------------+-------------+-----------------+---------------| | \K2 | Enter | Send break to | Send break to | | | command | remote modem | remote modem | | | mode, do | immediately | immediately | | | not send | | | | | break to | | | | | remote | | | | | modem | | | |------------+-------------+-----------------+---------------| | \K3 | Send break | Send break to | Send break to | | | to remote | remote modem | remote modem | | | modem | immediately | immediately | | | immediately | | | |------------+-------------+-----------------+---------------| | \K4 | Enter | Send break to | Send break to | | | command | remote modem | remote modem | | | mode, do | with | with | | | not send | transmitted | transmitted | | | break to | data | data | | | remote | | | | | modem | | | |------------+-------------+-----------------+---------------| | i \K5 | Send break | Send break to | Send break to | | | with | remote modem | remote modem | | | transmitted | with | with | | | data | transmitted | transmitted | | | | data | data | +------------------------------------------------------------+ +------------------------------------------------------------+ | COMPRESSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT %Cn | |--------------+---------------------------------------------| | Description: | Selects MNP5 data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | %C0 | Data compression disabled | |--------------+---------------------------------------------| | i %C1 | Data compression enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | CONNECT MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Nn [cmds] | |--------------+---------------------------------------------| | Description: | Sets connect mode | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \N0 | Normal mode enabled | |--------------+---------------------------------------------| | \N2 | MNP mode enabled | |--------------+---------------------------------------------| | \N3 | LAPM mode enabled | |--------------+---------------------------------------------| | i \N4 | LAPM mode enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Gn [cmds] | |--------------+---------------------------------------------| | Description: | Selects modem port flow control | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \G0 | Flow control disabled | |--------------+---------------------------------------------| | \G1 | Flow control enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | FLOW CONTROL TYPE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Qn [cmds] | |--------------+---------------------------------------------| | Description: | Sets type of flow control used by modem | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \Q0 | Flow control disabled | |--------------+---------------------------------------------| | \Q1 | Bidirectional XON/XOFF flow control enabled | |--------------+---------------------------------------------| | \Q2 | CTS flow control by DCE enabled | |--------------+---------------------------------------------| | i \Q3 | Bidirectional CTS/RTS flow control enabled | |--------------+---------------------------------------------| | \Q4 | XON/XOFF flow control by DCE enabled | |--------------+---------------------------------------------| | \Q5 | CTS flow control by DCE enabled. CTS low | | | until connection established | |--------------+---------------------------------------------| | \Q6 | Bidirectional CTS/RTS flow control enabled. | | | CTS low until connection established | +------------------------------------------------------------+ +------------------------------------------------------------+ | INACTIVITY TIMER | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Tn [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0-90 | |--------------+---------------------------------------------| | Unit: | 1 minute | |--------------+---------------------------------------------| | Description: | Sets the length of time that the modem does | | | not receive information before it | | | disconnects | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOCK SERIAL PORT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Jn [cmds] | |--------------+---------------------------------------------| | Description: | Sets operation of serial port speed | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \J0 | Serial speed locked | |--------------+---------------------------------------------| | \J1 | Serial speed follows connect speed | +------------------------------------------------------------+ +------------------------------------------------------------+ | LOOPBACK TESTS | |------------------------------------------------------------| | Format | AT [cmds] S16=n [cmds] | |--------------+---------------------------------------------| | Default: | 0 | |--------------+---------------------------------------------| | Range: | 0 - 125 | |--------------+---------------------------------------------| | Unit: | Bit-mapped | |--------------+---------------------------------------------| | Description: | Enables loopback tests | |--------------+---------------------------------------------| | Bit | Value | Function | |------+-------+---------------------------------------------| | 0 | i 0 | Local analog loopback test disabled | | | | | | | 1 | Local analog loopback test enabled | |------+-------+---------------------------------------------| | 1 | 0 | Not used | |------+-------+---------------------------------------------| | 2 | i 0 | Local digital loopback test disabled | | | | | | | 1 | Local digital loopback test enabled | |------+-------+---------------------------------------------| | 3 | i 0 | Modem is not performing remotely requested | | | | remote digital loopback test | | | 1 | | | | | Modem is performing remotely requested | | | | remote digital loopback test | |------+-------+---------------------------------------------| | 4 | i 0 | Modem is not performing locally requested | | | | remote digital loopback test | | | 1 | | | | | Modem is performing locally requested | | | | remote digital loopback test | |------+-------+---------------------------------------------| | 5 | i 0 | Remote digital loopback with local | | | | self-test disabled | | | 1 | | | | | Remote digital loopback with local | | | | self-test enabled | |------+-------+---------------------------------------------| | 6 | i 0 | Local analog loopback with local self-test | | | | disabled | | | 1 | | | | | Local analog loopback with local self-test | | | | enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | MAXIMUM BLOCK SIZE FOR TRANSMISSION | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \An [cmds] | |--------------+---------------------------------------------| | Description: | Sets the maximum transmittable block size | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | \A0 | MNP block size is 64 characters | |--------------+---------------------------------------------| | \A1 | MNP block size is 128 characters | |--------------+---------------------------------------------| | \A2 | MNP block size is 192 characters | |--------------+---------------------------------------------| | i \A3 | MNP block size is 256 characters | +------------------------------------------------------------+ +------------------------------------------------------------+ | MNP STREAM/BLOCK MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Ln [cmds] | |--------------+---------------------------------------------| | Description: | Selects the transfer mode for MNP | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \L0 | Stream mode for MNP enabled | |--------------+---------------------------------------------| | \L1 | Block mode for MNP enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | RESULT CODE FORMAT | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Vn [cmds] | |--------------+---------------------------------------------| | Description: | Selects format for information-text and | | | result codes | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | V0 | Numeric format enabled | |--------------+---------------------------------------------| | V1 | Verbose (word) format enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | SWITCH TO NORMAL MODE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Z [cmds] | |--------------+---------------------------------------------| | Description: | Switches to normal mode from MNP mode | +------------------------------------------------------------+ +------------------------------------------------------------+ | TEST TIME LIMIT | |------------------------------------------------------------| | Type | Configuration | |-------------+----------------------------------------------| | Format | AT [cmds] S18=n [cmds] | |-------------+----------------------------------------------| | Default | 0 | |-------------+----------------------------------------------| | Range | 0 - 255 | |-------------+----------------------------------------------| | Unit | 1 second | |-------------+----------------------------------------------| | Description | Limits time allowed for diagnostic test | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.42 DETECTION PHASE | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] -Jn [cmds] | |--------------+---------------------------------------------| | Description: | Controls V.42 detection | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | -J0 | V.42 detection disabled | |--------------+---------------------------------------------| | i -J1 | V.42 detection enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.42bis COMPRESSION CONTROL | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] "Hn [cmds] | |--------------+---------------------------------------------| | Description: | Controls V.42bis data compression | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | "H0 | V.42bis disabled | |--------------+---------------------------------------------| | "H1 | V.42bis when transmitting enabled | |--------------+---------------------------------------------| | "H2 | V.42bis when receiving enabled | |--------------+---------------------------------------------| | i "H3 | V.42bis when transmitting/receiving enabled | +------------------------------------------------------------+ +------------------------------------------------------------+ | V.42bis MAXIMUM STRING LENGTH | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] "O=n [cmds] | |--------------+---------------------------------------------| | Default: | 250 | |--------------+---------------------------------------------| | Range: | 6 -250 | |--------------+---------------------------------------------| | Unit: | Unidentified | |--------------+---------------------------------------------| | Description: | Selects string size for V.42bis compression | +------------------------------------------------------------+ +------------------------------------------------------------+ | XON/XOFF PASS-THROUGH | |------------------------------------------------------------| | Type: | Configuration | |--------------+---------------------------------------------| | Format: | AT [cmds] \Xn [cmds] | |--------------+---------------------------------------------| | Description: | Selects whether XON/XOFF signals are sent | | | to remote modem | |--------------+---------------------------------------------| | Command | Function | |--------------+---------------------------------------------| | i \X0 | XON/XOFF signals trapped by local modem | |--------------+---------------------------------------------| | \X1 | XON/XOFF passed through local modem | +------------------------------------------------------------+